Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
The writer is making several good pointers about Installing A Bathtub as a whole in this article just below.
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is readily available, the task can move rapidly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either instance, the job is within a home handyman's skills, although you will require a helper to vacate the old bathtub as well as set in the brand-new one. Ensure you have certified on your own for the job as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed task, it is better to take into consideration using one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your bathroom if you have already bought a brand-new bathtub and also don't require to change the setup of your previous water pipes.
Your tools and also product checklist should consist of the following:
Planning for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, switch on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be rather troublesome as a result of the restricted gain access to that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the needed setting. The wooden boards are valuable in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the level and changing the feet on the bath tub until the level reads level.
To set up taps, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water system as well as check all joints and also new pipework for leaks as well as tighten them if necessary. Fill the tub as well as likewise check the overflow electrical outlet and the regular outlet for leaks.
Finally, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the tub should wait up until the bathtub has actually been used at the very least once as this will certainly settle it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the tap and the sink. Protect the tap in place with the producer supplied backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The former kind should be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, resulting in complications with wetness as well as possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also installations. They are offered in tubes as well as cartridges, and also are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealer can fracture fairly very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily offered on the market. It is advisable to fit the tiles using waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our article on How to Install a Bathtub. Many thanks for taking time to browse our short article. Enjoyed our blog entry? Please share it. Let other people discover it. Kudos for your time. Visit again soon.
Schedule An Appointment Report this page